Your cart is empty

ImaxRC B610

ImaxRC B610 Twins


RC Smart Charger
Voltage Range: DC11.0~18.0 Volt
Max Circuit Power: 2*200 Watts
Max Discharge Power: 2*25 Watts
Charge Current Range: 0.1~10A
Discharge Current Range: 2*(0.1~5A)
Current Drain for Balancing Li-Po/Lon/Fe: 200Ma/cell
Li-ion/Fe/Polymer cell count: 1~6 cells
NiCd/NiMH battery cell count: 1~18 cells
Pb battery Voltage: 2~24V
Net Weight: 350g
Dimension: 160*200*60mm

Packing List
1X Charger ImaxRC B610 Twins
1X Instruction Manual
1X Cable Set:
   Tamiya charging cable
   FutabaRX charging cable
   Glow charging cable
   Crocodile clip charging cable
   JST/BEC charging cable
   Dean charging cable (2P)
2X 6PIN adapter
2X Crocodile clip

Imax RC B610 Twins Introduction
If you have been searching for one charger can charge two batteries at once, look no further than the IMAXRC B610Twins. It is a latest professional & rapid charger of 200W /each with dual output, totally output 400W. B610Twins is able to service multiple types of batteries, such as NiCd, NiMH, LiPO, Li-ION/LiFe and Lead Acid batteries.

Optimized operation software
B610Twins features an AUTO function that controls the charge rate during charging and discharging. For Lithium batteries, this can prevent overcharging which may lead to an explosion due to the user's setting the charge rate improperly. It will disconnect the circuit automatically and initiate an alarm if there is any malfunction. All the operating modes of this charger are controlled through two way communication, between the charger and the battery to achieve maximum safety. All the settings can be configured by the user.

Internal independent lithium battery balancer
B610Twins employs an individual cell voltage balancer. It isn't necessary to connect an external balancer for balancer charging.

How to use
1, Using the power cord, connect the charger to the 110~240VAC mains electricity (usual household wall socket).The 2control LED on the charger light green ,the charger is in standby mode.
2. Connect the battery to the charger as following, and push "on/off" button the charger will enter charge state, then 2 LED turn red. Figure 1: If a LED is flashing red, it means that the corresponding cell has a low voltage or connects with charger improperly. Check the connection state between balance port and charger, or check the voltage of corresponding battery cell. If battery is defective, discontinue use of this battery immediately.
3. When battery is fully charged and balanced, the LED will turn green. The charger sets 4 hours time limit after CV mode charging for balancing battery, if the battery is still unbalanced after 4 hours' balance charging, please reinsert and recharge them to achieve complete balance.

Balancing individual cells battery discharging
During the process of discharging, the B610Twins can monitor and balance each cell of the battery individually. An error message will be indicated and the process will be ended automatically if the voltage of any single one cell is abnormal.

"Fast" and "storage" mode of lithium battery
There are various methods of charging Lithium batteries. "Fast" charge reduces the charging time whereas "store charge" can control the final voltage of your battery. This method is best for long term storage and protects the useful life of the battery.

Automatic charging current limit& Temperature threshold
You can set the upper limit of the charge current when charging your NiCd or NiMH batteries. It is useful for NiMH batteries of low impedance and capacity in the 'AUTO' charging mode.The batteries internal chemical reaction can cause the temperature of the battery to rise during charging. If the temperature limit is reached (set by the user), the charging process will be terminated. This function is available by connecting an optional temperature probe, which is not included in with the charger.

Processing time limit& Data store/load& Cyclic charging/discharging
The user can set the maximum charging time. If the charging time exceeds the limit, the process will be terminated automatically when you set the maximum time for the charging mode. The "Duo" can store data from ten different batteries. The user can set the charging / discharging parameters for a particular battery type and "call up" these settings to charge a battery without additional programming needed. Batteries can be set to charge/ discharge for 5 cycles if needed.

ImaxRC B610


Add to Cart:

  • Model: AHY000616
  • Shipping Weight: 1kg
  • 10 Units in Stock
  • Manufactured by: ImaxRC



This product was added to our catalog on Monday 17 September, 2012.

www.hobbywin.com